Knowledge Base ISC Main Website Ask a Question/Contact ISC
Testing authoritative server support for EDNS and large UDP buffer sizes in BIND 9.10
Author: Cathy Almond Reference Number: AA-01350 Views: 11466 Created: 2016-03-01 10:45 Last Updated: 2017-02-20 19:24 0 Rating/ Voters

The EDNS fallback code was re-worked in BIND 9.10 to make it more resilient and reliable when:

  • Encountering new authoritative servers that have not been queried before and for whom the capabilities/support for EDNS and large buffer sizes by both the server and the network path between it and the resolver is unknown.
  • Facing intermittent network packet losses which, on older versions of BIND, can result in SERVFAILs due to servers that should support EDNS being marked as EDNS-incapable

The EDNS code in BIND 9.10 records successful plain and EDNS query counts as well at timeouts for plain DNS and EDNS queries at various EDNS buffer sizes: 4096, 1432, 1232 and 512 for each server named talks to.  A EDNS timeout for a lower buffer size is also counted against higher buffer sizes. These are held in 8 bit counters and are shifted on overflow of any counter. This will result in the removal from history of any false positives due to transitory network problems.

The buffer sizes of 1432 and 1232 are chosen to allow for a IPv4/IPv6 encapsulated UDP message to be sent without fragmentation at Ethernet and IPv6 network minimum MTU sizes.  Named also records the largest successful EDNS response size seen.

When querying a new server for the first time, named will send a EDNS query advertising a 512 byte UDP buffer. This is the most conservative EDNS message that can be sent.  If successful, subsequent queries will 'probe' the capabilities of the authoritative server by advertising successively larger EDNS sizes.

When querying a known server using EDNS, named will choose a EDNS buffer size based on the history of EDNS timeouts at various advertised sizes and also on the largest successful EDNS response that it has already received from that server.  Note however that named cannot learn that a server (and the path between itself and the remote server) can support larger UDP packet sizes until it successfully receives a large response from that server.

If any response results in a response with TC=1 being returned, then named will re-send the query using TCP - it will not take this opportunity to try with a larger advertised EDNS UDP packet size (because this might further delay getting a query response to the client).

If there are too many timeouts to EDNS queries and with successful plain DNS query responses recorded in the query counts, then named will fallback to using plain DNS when taking to a server, although it will still periodically send a EDNS query to see if the server now supports EDNS.

The Address database dump section of a cache dump now displays the counters being used to track success/failure history - for example:

;       192.0.2.30 [srtt 19320] [flags 00004000] [edns 3/0/0/0/0] [plain 0/0] [udpsize 1118] [ttl 1350]

The edns and plain counters are incremented as you would expect them to be as the responses are successfully received or timeouts are logged.  But as noted above, all of them are adjusted when any one of them overflows (a bitwise shift) in order to eliminate over time any false positives and counts of transient errors, and to force a periodic retry with EDNS (if the server has not yet responded to queries with EDNS) and again to probe larger EDNS packet sizes.

Their interpretation is provided at the start of the Address database dump section:

; [edns success/4096 timeout/1432 timeout/1232 timeout/512 timeout]
; [plain success/timeout]

ADB server entries persist for up to 10 minutes.  They are displayed by name(s) as well as address unless address entries (A and AAAA) have expired from cache, in which case they appear only in the Unassociated entries table in the cache dump.  (But they may be re-associated with their name(s) later, if the cache information is refreshed).

Queries from named may advertise what appear to be unusual EDNS sizes

Although the Address Database entry in cache for each server stores the counters for timeouts at various EDNS buffer sizes (4096, 1432, 1232 and 512), named may also advertise intermediate values when querying.  This is because named records the size of the biggest response successfully received so that it can use that value instead of 512 for a 'conservative' EDNS size advertisement.


© 2001-2017 Internet Systems Consortium

For assistance with problems and questions for which you have not been able to find an answer in our Knowledge Base, we recommend searching our community mailing list archives and/or posting your question there (you will need to register there first for your posts to be accepted). The bind-users and the dhcp-users lists particularly have a long-standing and active membership.

ISC relies on the financial support of the community to fund the development of its open source software products. If you would like to support future product evolution and maintenance as well having peace of mind knowing that our team of experts are poised to provide you with individual technical assistance whenever you call upon them, then please consider our Professional Subscription Support services - details can be found on our main website.

Feedback
  • There is no feedback for this article
Quick Jump Menu